Autodesk has changed the installation requirements and behavior for Inventor service packs going forward: Service Pack 1 is no longer required to be installed as a prerequisite for the installation of Service Pack 2. Service Pack 2 includes all fixes included in Service Pack 1. If you are updating from the release version of Inventor 2012, you only need to install Service Pack 2 to obtain the latest updates.
Uninstalling Inventor 2012 Service Pack 2 uninstalls Service Pack 2 only and maintains Service Pack 1 and/or any Hotfixes you may have installed previously. This is the new standard for Inventor Service Pack behavior and will hold true for any subsequent service pack releases for 2012 and 2013.
Here is the link to download Inventor 2012 SP2 32-bit, Click Here...
Here is the link to download Inventor 2012 SP2 64-bit, Click Here...
Here is a link for the Readme file, Click Here…
Here is a link to see what issues were addressed for SP1, Click Here...
Follow the break to see the issues addressed by SP2.
- Geometry for simulation can sometimes become distorted after excluding patterns or assembly features.
- FEAComputeServer.exe has stopped working message occurs rarely on certain models and simulations.
- Promote configuration or material to model does not automatically trigger updates.
- NG: Load is sometimes ignored when applied to very small faces compared to the overall size of the part (small face is ignored in the mesh).
- NG: HTML report generation fails if logo image source location is the same as the report target location.
- NG: During batch solving, the Cancel button prematurely changes to Close after the first simulation is completed.
Dynamic Simulation
- CER: A crash occurs when you enable automatic conversion of assembly constraints to joints in particular models.
- CER: A crash occurs if you re-enter the environment after assembly modification on XP-32 systems.
- CER: A crash occurs while you edit 3D Contact joint properties under certain conditions.
- Encountered an improper argument message displays after you accept the joint properties dialog box the first or second time after creating a motion load analysis.
- CER: Inventor becomes unresponsive or crashes if you click mechanism status on some over-constrained simulations (after converting constraints and welding mobile parts).
Frame Analysis
- Rotation for custom constraint displays only fixed type in report.
- NG: HTML report generation fails if logo image source location is the same as the report target location.
Tooling
- Mold design assembly migration fails with Task Scheduler.
AEC Exchange
- CER: Inventor crashes when you enter BIM Exchange with a file missing from an assembly.
API
- Export DWF with DataIO.WriteDataToFile in ApprenticeServer raises "whiptk_wt_ns.7.12.601.dll can't be loaded" error.
- Get DrawingCurves based on an iFeature raises an error.
- Get DrawingCurves based on an iFeature raises an error.
- GeneralDimensions.AddLinear does not work when passing intent created on 3D sketch geometry.
- DrawingCurve that is from thread feature does not return start/end/mid points.
- OnOpenDocument returns the wrong top level document when it opens a document by its referencing drawing document.
- AssemblyConstraint.EntityTwo returns a proxy object incorrectly when the sub-assembly is being in-place edited.
- Access WorkSurface properties returns an error for some model data.
- Change ActiveTableRow for iFeatureTable does not work when it has custom values.
Assembly Modeling
- The color of occurrence is wrong when you change the Design View.
- Inventor crashes when you change the LOD in a sub-assembly.
- Inventor crashes when you replace the component.
- Inventor crashes when you press the Enter key while you hold down the left mouse button after you enter an offset value for an offset workplane.
- Inventor crashes when you input the Count of a pattern with another document active.
- A crash occurs when you update a parameter of a component that is linked to the assembly.
- CER: Inventor crashes when you save a particular assembly.
- CER: Inventor crashes when switch from Face Fillet to Edge Fillet on fillet dialog when retry a face fillet.
- Inventor crashes when you create a constraint for two components.
Content Center
- Refreshing a Tube & Pipe part fails when a Tube & Pipe Addin is not loaded.
- CER: A crash occurs when you insert certain Content Center files.
Direct Manipulation
- Fixed sync update for retrieve dimension.
Drawing Manager
- Fixed sync update for retrieve dimension.
- Inventor crashes when you select an .idw file, and click Print on the context menu.
- CER: A crash occurs when you define a new base point on the DWG file.
- Measure Distance tool in Drawing Manager does not correctly measure the diameter.
- CER: A crash occurs when you right click on the document name.
- Design Views are not honored after you apply Service Pack 1 with Cable & Harness information.
- A Bug Alert displays when you delete a raster view.
- NG: Drawing View placement is inconsistent when you check "Create projected views immediately after base view creation".
Enhanced Visualization
- Unable to record a drive constraint into an avi file.
- CER: With all addins unloaded, Inventor sometimes crashes when you use New or Open a document, and then exit it directly.
- Sketch Degrees of Freedom symbols do not show in a face.
- CER: Inventor crashes when you enable Software Graphics under the Performance or Quality settings on an XP operating system.
- CER: Runtime error R6025-pure virtual function call generates, and Inventor crashes when you resize the window and zoom during an in place edit, and Shaded with Hidden Edges.
Framework
- CER: Inventor crashes when you double-click Route after undo and redo of the Finish Route command.
- Error message "File not found" displays while you open several Inventor files together in XP operation system.
- CER: Inventor crashes when you open a part file that was created in an Educational version.
- CER: Inventor crashes when you resolve a part file with the active shared project.
- A crash sometimes occurs when you perform a manipulation in the Add-Ins dialog box.
Frame Generator
- Length of merged frames is incorrect with non-center orientation.
- CER: Deleting the constraints causes Inventor to shut down.
iLogic
- Inventor crashes when you close an Inventor file and then invoke Design Copy and check files to copy.
- In a Vault project, you cannot use the Add Rule command in a drawing if a user is logged in.
Part Modeling
- When you edit a master sketch, all of the derived parts within the assembly require an update.
- Inventor crashes when you update a derived part.
- Inventor crashes when you use derive with single composite feature style.
- The upstream sketch dimensions are not hidden after you apply a feature.
- A crash occurs when you invoke Hole with one reference edge selected.
- Keep the last input status for options when invoking the Hole command again.
- Inventor crashes when you choose a Cut together with a Work Plane to create iFeature.
- Inventor crashes when you insert an ifeature and then Undo the insert.
- Inventor crashes when you activate the ipart member after you modify its parameter.
- Inventor crashes when you make components to select corrupt solids.
- If the Sheet Metal Parameters folder is collapsed, changing a Model parameter sometimes makes a row unselectable.
- Crash occurs when you create a rectangular pattern using curve length and two across directions.
- Crash occurs when you create a rectangular pattern along some sketch curves.
- Crash occurs if you hit the Backspace key with the Replace face dialog box displayed.
- Inventor crashes when you open a file and then activate the Split command.
- Inventor crashes when you edit a split feature.
- Crashes occur in a Split feature using the Split Into Two Bodies option.
- Inventor crashes when you switch Sweep type from Path to Path & Guide Rail.
- NG: Work features Edge View is incorrect.
- CER: A crash occurs when you refit surfaces imported from Alias in Construction Environment.
- CER: Inventor crashes when you copy a face on a specific model.
Presentation
- Inventor locks up when you turn Defer Update off on a drawing.
Sketch
- CER: A crash occurs when you generate the sketch block.
- Inventor crashes when you create a block for certain sketch geometries.
- Regress: Bug Alert when copy AutoCAD geometry to Inventor Sketch environment.
- CER: Inventor crashes when you select some lines for a Close Loop.
- CER: A crash occurs when you right-click the Sketch name.
- A crash sometimes occurs when you dynamically drag sketch geometry.
- CER: A crash occurs while you finish editing a 2D sketch.
- Inventor sometimes crashes when you add a linear dimension to a sketch.
- CER: A crash occurs after you click Break link in the Sketch environment.
- CER: Inventor crashes when you move the End of Part.
- CER: A crash occurs after you edit a pattern in a sketch and finish the sketch.
- Inventor crashes after you change the value of a parameter.
- CER: Inventor crashes when you edit a pattern in the 2D sketch.
- A crash occurs when you reduce the count of a sketch pattern to 1 with the parameters.
- A crash occurs after you delete a constraint in a 3D sketch.
Translators
- Inappropriate geometry is generated when you export certain drawings to PDF/DWF.
- Fix copying/pasting AutoCAD object to Inventor.
- Export to DXF with Pack and Go option checked does not create a zip file in 64 bit operating systems.
- Empty files sometimes occur in Inventor when it reads STEP files.
- Wrong STEP AP203 schema is used when exported.
- CER: A crash occurs when you save some specific files to STL on a 32 bit XP operating system.
- A crash occurs when Inventor reads CATIA files when the translation report does not embed successfully.
No comments:
Post a Comment
Note: Only a member of this blog may post a comment.